Audio Oscillator CHOP

From TouchDesigner 099 Wiki

Summary

The Audio Oscillator CHOP generates sounds in three ways. It repeats common waveforms (sine, triangle), it generates white noise (a random number for each sample), or it repeats a prepared incoming audio clip of any duration. It outputs typically 44100 samples per second. In contrast, the LFO CHOP by default generates waves at lower frequencies and lower sample rates (60 samples/second), however both Audio Oscillator and LFO are interchangeable by changing their frequencies and sample rates.

When it is synthesizing tones from the basic waveforms, the Audio Oscillator CHOP steps through the waveform at a rate that depends on the Pitch Control input. By default, a Pitch Control of 0 gives a middle A at 440 Hz; a 1 gives 880 Hz; a -1 gives 220 Hz. Steps of 1 in Pitch Control are 1 octave apart. Steps of 1/12 (.08333) are 1 semitone apart.

Up to three input CHOPs can be connected to the Audio Oscillator CHOP.

Pitch Control - The first (optional) input affects the pitch. Output channels are generated for each Pitch Control channel. When pitch control is 0, it outputs a wave at the base frequency (default 440 Hz at 44,100 samples per second). It is "logarithmic": By default, increasing the pitch control by 1 increases the pitch by 1 octave, by 2 it increases by 2 octaves (4 times the frequency).

Reset Pulse - The second (optional) input contains pulses that restart the oscillator from the beginning of the wave or the Playback Source. 0 in the input means "play the oscillator". 1 means "stop the oscillator and cue it at the start of the waveform or Playback Source".

Playback Source - The third (optional) input is a replacement of the waveform Type. It is a sound clip to play at a rate modified by the Pitch Control, and can contain any number of channels. These channels are generated for each Pitch Control channel. The waveform Type and the Base Frequency parameters are disabled.

If you plug any sound clip into the Audio Oscillator CHOP's Playback Source, and Pitch Control is a constant value of 0 of any duration, it will just repeat the Playback Source. If you feed a Wave CHOP as its Pitch Control, it will raise and lower the speed/pitch of the input.

The Audio Oscillator CHOP can serve as a general motion time-warper and repeater. If you put motion channels into the third input, you can control the time warp by feeding different Pitch Control curves. 0 pitch is normal speed, 1 is double speed.

Unlike the Wave CHOP, this is an iterating CHOP, that is, it steps through the waveform while the pitch changes. To see this effect, feed an LFO CHOP into the Audio Oscillator. Unlike the LFO CHOP, the Audio Oscillator CHOP is designed for audio frequencies.

See also: LFO CHOP, Wave CHOP.

PythonIcon.png audiooscillatorCHOP_Class

Parameters - Waveform Page

Type - The shape of the waveform to repeat, unless overridden by the Playback Source:

  • Sine (-1 to 1)
  • Gaussian (0 to 1)
  • Triangle (-1 to 1)
  • Ramp (0 to 1)
  • Square (-1 to 1)
  • Pulse (0 to 1)
  • White Noise Random samples between -1 and 1

Base Frequency frequency - The cycles per second when the Pitch Control is zero.

Units per Octave octave - Amount that the Pitch Control needs to increase by to raise the pitch by one octave. The default of 1 means that Pitch Control of 1 raises the pitch by 1 octave. Units per Octave of .08333 means that a Pitch Control of 3 raises the pitch by a factor of 3 x .08333 (three semitones). This is suitable for using MIDI note numbers as pitch control.

Offset offset - Values output from the CHOP can have an offset added to them.

Amplitude amp - Values output from the CHOP can be scaled.

Bias bias - Shape control for Triangle, Gaussian and Square waves. For triangle waves, it moves the peak. For square waves, it alters the width of the peak. Zero means no bias.

Phase phase - A value of .5 is a phase shift of 180 degrees, or one half cycle.


Smooth Pitch Changes - If the Pitch Control channel input to the Audio Oscillator CHOP is rising and is running at the Touch default of 60 frames per second, then the pitch will hold for 1/60 second before stepping up for another 1/60 second. This is an audible step. With this option On, the pitch rises for every audio sample, giving perfectly smooth glissando at extra compute cost.

Reset Condition - This menu determines how the Reset input triggers a reset of the channel(s).

  • Off to On - channels are reset when the Reset input goes off to on.
  • While On - channels are reset when the Reset input goes on. The channel will hold the reset value until the input turns off.
  • On to Off - channels are reset when the Reset input goes on to off.
  • While Off - channels are reset when the Reset input goes off. The channel will hold the reset value until the input turns on.

Reset - This button resets the channel(s) to 0.

Parameters - Channel Page

Sample Rate - The sample rate of the CHOP. The default sample rate is 44100 Hz.

Standard Options and Local Variables

None.