DMX In CHOP
Summary[edit]
The DMX In CHOP receives channels from DMX, Art-Net or sACN devices. Channel values for DMX are 0-255. Note that input rate is limited to the DMX maximum refresh rate of 44Hz.
A Filter Table can be provided in a DAT where addresses can be specified by adding rows for each channel and specifying net, subnet and universe.
ENTTEC NOTE: - Use ENTTEC's NMU (Node Management Utility) to configure and inspect the ENTTEC devices found on your network.
See also: Art-Net, DMX Out CHOP
Parameters - Port Page
Active active
- Connects to the device while On.
Interface interface
- ⊞ - Select the type of interface to connect to the device with.
- Enttec Generic Serial
serial
- Uses the operating system's serial calls to read data.
- Enttec USB Pro
enttecusbpro
-
- Enttec USB Pro Mk2
enttecusbpromk2
-
- Art-Net
artnet
- Sets the interface to Art-Net protocol.
- sACN
sacn
- Sets the interface to sACN protocol.
Device device
- Select a DMX device from the menu.
Serial Port serialport
- When the Interface parameter is set Generic Serial this parameter lets you select which Serial (COM) port to use.
Format format
- ⊞ - Select between receiving Packet Per Sample (Timesliced), Packet Per Channel (Latest) or Packet Per Channel (All). When selecting Packet Per Channel (Latest), any messages outside the last cook are being discarded while the option Packet Per Channel (All) will append channels that would get otherwise skipped by dropped frames.
- Packet Per Sample (Timesliced)
packetpersample
-
- Packet Per Channel (Latest)
packetperchan
-
- Packet Per Channel (All)
packetperchanall
-
Art-Net Net (0-127) net
- When the Interface parameter is set to Art-Net, this sets the net address. A net is a groups of 16 consecutive subnets or 256 consecutive universes. The range for this parameter is 0-127. This is not a network IP address.
Art-Net Subnet (0-15) subnet
- When the Interface parameter is set to Art-Net, this sets the subnet address. A subnet is a group of 16 consecutive universes. The range for this parameter is 0-15. This is not a network subnet mask.
Art-Net Universe (0-15) universe
- When the Interface parameter is set to Art-Net, this sets the universe address. A single DMX512 frame of 512 channels is referred to as a universe. The range for this parameter is 0-15.
Filter Table filterdat
- Available when using Packet Per Channel Format for Art-Net or sACN. Use the docked Table DAT to specify which net, subnet, universe channels are being received from.
Note: For sACN the first available universe has the index 1 as universe 0 is reserved by the system for future use.
Net Name netname
- Specify the channel prefix for the net part of the address.
Subnet Name subnetname
- Specify the channel prefix for the subnet part of the address.
Universe Name universename
- Specify the channel prefix for the universe part of the address.
Start Codes startcodes
- A list of accepted start codes when using sACN. If the DMX In CHOP receives an sACN packet with a start code not in the list then it will discard it.
Multicast multicast
- Enable multicast for sACN. Multicast automatically builds the IP based on Net, Subnet, and Universe of the device. This allows for the DMX In CHOP to automatically receive from a sender without knowledge of it's address.
Queue Size queuesize
- When using interface Art-Net or sACN, this will set the size of the incoming packets queue. This can be used to smooth data, though latency will be higher. In the case of Packet Per Channel (All), this parameter controls the maximum number of packets created per cook.
Rate rate
- Resample the incoming data to this rate.
Parameters - Common Page
Time Slice timeslice
- Turning this on forces the channels to be "Time Sliced". A Time Slice is the time between the last cook frame and the current cook frame.
Scope scope
- To determine which channels get affected, some CHOPs use a Scope string on the Common page.
Sample Rate Match srselect
- ⊞ - Handle cases where multiple input CHOPs' sample rates are different. When Resampling occurs, the curves are interpolated according to the Interpolation Method Option, or "Linear" if the Interpolate Options are not available.
- Resample At First Input's Rate
first
- Use rate of first input to resample others.
- Resample At Maximum Rate
max
- Resample to the highest sample rate.
- Resample At Minimum Rate
min
- Resample to the lowest sample rate.
- Error If Rates Differ
err
- Doesn't accept conflicting sample rates.
Export Method exportmethod
- ⊞ - This will determine how to connect the CHOP channel to the parameter. Refer to the Export article for more information.
- DAT Table by Index
datindex
- Uses the docked DAT table and references the channel via the index of the channel in the CHOP.
- DAT Table by Name
datname
- Uses the docked DAT table and references the channel via the name of the channel in the CHOP.
- Channel Name is Path:Parameter
autoname
- The channel is the full destination of where to export to, such hasgeo1/transform1:tx
.
Export Root autoexportroot
- This path points to the root node where all of the paths that exporting by Channel Name is Path:Parameter are relative to.
Export Table exporttable
- The DAT used to hold the export information when using the DAT Table Export Methods (See above).
TouchDesigner Build:
CHOPs |
---|
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • |