Extend CHOP

Summary

The Extend CHOP only sets the "extend conditions" of a CHOP, which determines what values you get when sampling the CHOP before or after its interval.

The Extend CHOP has separate menus to control both the pre-interval and the post-interval. For example, before the interval, you may want to hold a constant value, and after the interval you may want to cycle or repeat the curves in the interval.

To shorten or lengthen the interval (the start or end of the CHOP), use the Trim CHOP.

You can see the state of Extend Conditions in the pop-up info of any CHOP (use middle-mouse click on the CHOP).

extendCHOP_Class

Parameters - Extend Page

Left Behavior left - ⊞ - The extend condition before the CHOP interval. They are:

Right Behavior right - ⊞ - Extend condition after the interval. Same options as Extend Left.

Default Value defval - The value used for the Default Value extend condition.

Parameters - Common Page

Time Slice timeslice - Turning this on forces the channels to be "Time Sliced". A Time Slice is the time between the last cook frame and the current cook frame.

Scope scope - To determine which channels get affected, some CHOPs use a Scope string on the Common page. See Pattern Matching.

Sample Rate Match srselect - ⊞ - Handle cases where multiple input CHOPs' sample rates are different. When Resampling occurs, the curves are interpolated according to the Interpolation Method Option, or "Linear" if the Interpolate Options are not available.

• Resample At First Input's Rate first - Use rate of first input to resample others.

• Resample At Maximum Rate max - Resample to the highest sample rate.

• Resample At Minimum Rate min - Resample to the lowest sample rate.

• Error If Rates Differ err - Doesn't accept conflicting sample rates.

Export Method exportmethod - ⊞ - This will determine how to connect the CHOP channel to the parameter. Refer to the Export article for more information.

• DAT Table by Index datindex - Uses the docked DAT table and references the channel via the index of the channel in the CHOP.

• DAT Table by Name datname - Uses the docked DAT table and references the channel via the name of the channel in the CHOP.

• Channel Name is Path:Parameter autoname - The channel is the full destination of where to export to, such has geo1/transform1:tx.

Export Root autoexportroot - This path points to the root node where all of the paths that exporting by Channel Name is Path:Parameter are relative to.

Export Table exporttable - The DAT used to hold the export information when using the DAT Table Export Methods (See above).

Operator Inputs

• Input 0: -

TouchDesigner Build: Latest\n2022.241402021.100002018.28070before 2018.28070

An Operator Family which operate on Channels (a sequence of numbers (Samples)) which are used for animation, audio, mathematics, simulation, logic, UI construction, and data streamed from/to devices and protocols.

In CHOPs, Extend Conditions determine what numbers you get when you try to get a channel value that is outside its start-end range - in its Extend Regions.

A Time Slice is the time from the last cook frame to the current cook frame. In CHOPs it is the set of short channels that contain the CHOP channels' samples between the last and the current cook frame.

A parameter in most CHOPs that restricts which channels of that CHOP will be affected. Normally all channels of a CHOP are affected by the operator. TOPs have Channel Mask, a similar feature.

samples-per-second of a CHOP. Each CHOP in your network has a sample rate. In contrast, the overall timeline has a Frame Rate, which is the number of frames to cook and display per second, generally your monitor display frequency, default 60.

Exporting is the connection of CHOP channels to parameters of operators. The output of each exporting CHOP is one or more channels, active only while the CHOP Viewer is on. The current value of a channel can be exported to a parameter of any operator, overriding that parameter's value. See Parameter.

An Operator Family that manipulates text strings: multi-line text or tables. Multi-line text is often a python Script or GLSL Shader, but can be any multi-line text. Tables are rows and columns of cells, each containing a text string.

The location of an operator within the TouchDesigner environment, for example, /geo1/circle1, a node called circle1 in a component called geo1. The path / is called Root. This path is displayed at the top of every Pane, showing which Component's network you are currently in. To refer instead to a filesystem folder, directory, disk file or http: address, see Folder.

Every operator in TouchDesigner has a set of control Parameters that can be integer or floating point numbers, menus, binary toggles, text strings or operator paths, which determine the output of the operator.

TouchDesigner is a hierarchy of components. "root" is the top-most network in the hierarchy. The Network Path or Path for root is simply /. A typical path is /project1/moviein1.